logo
กรณี บริษัท ล่าสุดเกี่ยวกับ
รายละเอียดการแก้ไข
Created with Pixso. บ้าน Created with Pixso. โซลูชั่น Created with Pixso.

Carbide Burr Shapes: The 13 Standard Profiles and What Each Is For

Carbide Burr Shapes: The 13 Standard Profiles and What Each Is For

2026-11-17

Carbide Burr Shapes: The 13 Standard Profiles and What Each Is For

There are 13 standard carbide burr shapes, coded SA through SN. The letter is the shape; Most buyers who order the wrong burr have the material and the cut figured out. The problem is reach: they pick a profile that can't physically get at the surface. An SA where the job needs an end cut, a ball where a fillet was needed, a flame where the corner has to be square.

This chart covers all 13 profiles: what each one reaches and where each one fails. If you already know your shape code and just need speed data, head to the carbide burr RPM chart instead.

How Burr Shapes Are Coded

กรณี บริษัท ล่าสุดเกี่ยวกับ Carbide Burr Shapes: The 13 Standard Profiles and What Each Is For  0

The 13-shape system is set out in ISO 7755 (hardmetal burrs), and the same SA–SN letters turn up in North American and European catalogues alike. Every burr we supply follows this coding, so a shape code on your purchase order will match what arrives.

Two things about the code trip up first-time buyers.

First, the letter is the shape, the number is the size. SA-1 through SA-9 are nine sizes of one shape. A catalogue listing "SA-1, SA-2, SA-3…" isn't offering nine shapes, just nine diameters and lengths of the same cylinder. And the number doesn't run on a universal scale. SA-5 and SD-5 are both "size 5" within their own families, but the two heads aren't the same dimension.

Second, similar-looking codes are genuinely different tools. SA, SB and SC are all cylinders. In use they behave nothing alike. The difference is entirely at the end of the head.

We can cross-reference DIN to ANSI on request. Send the drawing and we'll confirm the equivalent before you order.


The 13 Shapes at a Glance

Code Shape What the end looks like Best used for Where it fails
SA Cylindrical, no end cut Flat top, no teeth on the top Straight edges, weld dressing on plate, finishing slot walls Cannot plunge — the flat face rubs and burnishes instead of cutting
SB Cylindrical, with end cut Flat top with cutting teeth Plunge cutting, squaring a corner, opening and enlarging holes, spot facing Plunge cutting, squaring a corner, opening and enlarging holes, spot facing
SC Cylindrical, radius end Rounded corner on a cylindrical body Rounded corner on a cylindrical body Tilting the tool leaves a visible step at the radius
SD Ball Full sphere Contoured surfaces, radii, hollowing, deburring inside curves Small contact patch — wears fast if you lean on it
SE Oval (egg) Elliptical Soft contours, blending on curved castings, aluminium and brass Will not sit flat; poor choice for flat-bottom work

SF

Tree, radius end Tapered body, rounded top Bottom of deep pockets, internal fillets, cavity work Long reach invites chatter — keep overhang short

SG

Tree, point end Tapered body, pointed top Starting a hole, chamfering, tight internal corners, opening narrow slots The point is the weakest section; avoid side loading
SH Flame Flame profile General deburring, weld seams, mixed contours — the best single-burr compromise Good at many jobs, best at none
SJ Cone, 60°, radius 60° included angle Chamfering, deburring hole edges, 60° seat preparation Angle must match the print or the seat will not seal
SK Cone, 90°, radius 90° included angle Chamfering, countersink preparation, edge breaking Same — verify the angle before ordering
SL Taper, radius end Long taper with rounded tip Tapered slots, dovetail forms, narrow angled recesses A slightly bent shank makes a taper run out immediately
SM Cone, point end Sharp-pointed cone Deburring small holes, fine detail, scribing Tip is very fragile; unsuitable for heavy stock removal
SN Inverted cone Cone with the tip inverted Back deburring, chamfering the far side of a through hole, T-slots Needs clearance behind the workpiece


Five profiles cover most of our catalogue: SA, SB, SC, SG and SL. That's what die, mould, weld and fabrication work actually asks for. All 13 are available to order; 


Cylindrical, Tree, Ball or Cone: Choosing by Task

Shape selection should start from the surface, not from the catalogue. Work backwards from what you need to reach:

Your task Start with Why this one
Deburring a straight edge or weld seam

SA, SC

Flat side wall presents the most teeth to a straight edge
Enlarging or opening a hole

SB, SG

Both cut on the end, so they can feed axially
Blending a fillet into a flat face

SC, SD

Radius matches the fillet without undercutting the face
Hollowing a curved surface

SD, SE

Spherical and elliptical profiles follow curvature in any direction
Cleaning the bottom of a deep pocket

SF, SL

Tapered body reaches past the walls without rubbing them
Back chamfering a through hole

SN

Only profile designed to cut on the far side
Chamfering a hole edge

SJ, SK

Fixed included angle gives a repeatable chamfer
One burr for mixed general work

SH

Flame profile is the accepted general-purpose compromise


Shape and Cut Have to Be Chosen Together

The shape decides where the burr can reach; the cut decides how it behaves once it's there. Specify one without the other and you get a tool that fits the job but finishes badly.

  • Single cut has one flute direction. It removes material fast and clears large chips, which suits aluminium, brass, copper and soft steel. Those same long chips are why it clogs on gummy materials without a lubricant.
  • Double cut has a cross-hatch tooth pattern. It breaks chips into small fragments, cuts more smoothly and gives noticeably better control at the same feed. That makes it the default for stainless, hardened steel and any job where surface finish matters. Roughly three quarters of the burrs in our own catalogue are double cut, because that's what European and North American machine shops order for steel and stainless.
  • Non-ferrous (aluminium) cut is a coarse single flute with deep gullets, designed to stop aluminium welding itself to the teeth. On 6061 or casting alloys, a standard double cut will cost you more in cleaning time than the right tool costs to buy.
  • Diamond cut is a separate category entirely, for hardened steel above 55 HRC, ceramics and carbide itself.

Tooth geometry and flute count change how aggressively a given shape cuts, whichever cut you choose. That's covered separately in how carbide burr tooth geometry affects cutting performance.


Six Mistakes That Account for Most Wrong Orders

  1. Ordering SA when the job needs SB. Both are cylinders, and the difference is invisible in a thumbnail photo. SA has a plain flat end and can't plunge. If any part of the operation feeds the tool into the work along its axis, you need SB. See cylindrical SB burrs.
  2. Mixing 6 mm and 1/4" shanks. 1/4" is 6.35 mm. A 6 mm shank will slide into a 1/4" collet but only grips a narrow band and slips under load; a 1/4" shank won't go into a 6 mm collet at all. Both sizes are common in our range — 1/4" is roughly half the catalogue, 6 mm most of the rest — so check which collet your grinder actually has. The same trap applies to 3 mm versus 1/8" (3.175 mm).
  3. Choosing head size for reach rather than for the grinder. A larger head needs more torque and runs at lower RPM. Put a 1/2" head on a low-power die grinder and you get chatter, not faster removal. Our speed and feed reference gives the ceiling by head diameter and material.
  4. Picking a shape by appearance. A ball looks versatile, and on curved surfaces it is. On a flat edge the contact patch is a single point, which is why ball burrs wear out fastest in shops that deburr plate.
  5. Ignoring the angle on cone burrs. SJ is 60°, SK is 90°. If a screw seat needs to seal, a chamfer at the wrong included angle will leak however clean the finish looks.
  6. Buying a burr to fix a hardness problem. Carbide burrs cut hardened steel, stainless and cast iron comfortably, but not every grade suits every hardness. If the tool is glazing instead of cutting, you need a different grade or a diamond burr. Changing the shape won't fix it.


How to Specify a Burr Order

For an accurate quote we need five things: shape code and size (SA-5, for example), head diameter × length, shank diameter, cut type and quantity. If all you have is a drawing or a sample, send either. We'll identify the profile and confirm the equivalent code before production.

If you'd rather have a stocked assortment than individual sizes, carbide burr sets put the common shapes in one case. That's usually the cheaper way to work out which profiles your work actually needs. 

Not sure which profile you need? Tell us the material, the feature you're deburring or blending, and the tool you're running it in. We'll recommend a shape, a cut and a starting RPM. If no standard profile will reach the feature, we can make a custom head to your drawing.


FAQ

What do the letters SA, SB and SC mean on a carbide burr?

They're shape codes from ISO 7755, used in North American and European catalogues alike. SA is a cylinder with no end cut, SB is the same cylinder with an end cut, and SC has a radius end. The letter defines the profile; the number defines the size within it.


What is the difference between SA and SB burrs?

Only the end. SA has a plain flat face with no cutting teeth, so it works on side walls but can't be plunged. SB has teeth across the end face, so you can feed it straight into the work to open holes or square corners.


How many standard carbide burr shapes are there?

Thirteen: SA, SB, SC, SD, SE, SF, SG, SH, SJ, SK, SL, SM and SN. Custom and modified profiles exist too, but those thirteen cover almost all standard deburring, blending and stock removal work.


Can I use a 6 mm shank burr in a 1/4" die grinder?

Only if the collet is genuinely 6 mm. 1/4" is 6.35 mm, so a 6 mm shank sits loose in a 1/4" collet and slips under load. A 1/4" shank won't fit a 6 mm collet at all. Check the marking on the collet instead of assuming.


Single cut or double cut for stainless steel?

Double cut. The cross-hatch pattern breaks chips small, cuts more smoothly and gives better control in work-hardening alloys. For aluminium, brass and soft steel, single cut is better when fast stock removal and chip clearance matter more than finish.


Which burr shape is best for general deburring?

There is no single "best" shape for every job, because the right burr depends on the edge or contour you are cleaning. However, a few shapes cover most general deburring tasks: SA-5, SC-5, SF-5, SG-5